Tube Hardware & Accessories



We have decided to discontinue selling vacuum tubes (valves) and refer customers to a company who specializes in tube sales, allowing us to refocus on other guitar amp parts.  
Click on the logo below to visit Eurotubes at eurotubes.com.    Quality products, great selection,  good prices and excellent customer service on all of your tube needs.

Tube Speciality Items     Retainers and Shields     8-Pin Sockets     9-Pin Sockets

 



Click on photo for
larger view
Solid-State Tube Rectifier Replacement.
Replaces 5AR4, GZ34, 5U4, 5Y3 rectifier tubes.  Use when less "sag" is desired in the power supply.  1.31"  diameter, 0.89" tall (not including pins and center post).  

Costs about 35% less than a new rectifier tube, and unlike tubes, should last indefinitely.    No deterioration over time.   Doesn't generate any heat, which lowers the heat given off by the amp.

NOTE! Because there is no warm up of a rectifier tube when using this solid state device, it is absolutely necessary that a standby switch is used in conjunction with this device.   Do not install in an amplifier that does not have a standby switch - always use the standby switch in amps so equipped when using the TSSR01.
Part #TSSR01

$14.95  

Click on photo for
larger view

Revisit™ BiasEasy200
Cathode Current Measuring Probe

For 8-pin power tubes such as 6L6, 6V6, 5881, 6550, EL34, KT88, KT66, KT100,  etc.   Requires separate digital volt-ohmmeter capable of reading current.   This device reads cathode current. 
Note:  This adapter will NOT test 7591 tubes.  Quality throughout, with a ceramic socket, gold-plated socket pins and gold-plated banana plugs to ensure solid connections and accurate readings.

Not a kit - this device is fully assembled and ready to use!  Complete with detailed instructions.   Used with a basic multimeter (Get Yours Here).  
Part #RBE-200

$29.95


 

Click on photo for
larger view

Revisit™ BiasEasy800
The Bias Easy™ 800 measures the current in the power tubes of your amp. Includes two 8-pin probes with gold plated pins and socket, power adapter and  operating instructions.  Fully assembled and ready to use.  For 8-pin power tubes such as 6L6, 6V6, 5881, 6550, EL34, KT88, KT66, KT100, etc.   Not for 7591 tubes.

The Bias Easy™ 800 allows you to monitor the bias setting safely and easily. While adjusting the bias control pot of your amp, the Bias Easy™ shows the actual current flowing through each of two power tubes.   A switch on the meter allows you to go back and forth between the two tubes.  This lets you set and evaluate the full reasonable biasing range your amp and tubes offer so that you may find the perfect setting.  Complete instructions are included.

The bias setting has a dramatic impact on the amp's tone, response, break-up and dynamic character.
Part #RBE-800

$89.95


 

Click on photo for
larger view

Revisit™ BiasEasy1200 Quad Tube Amp Bias Tester
The Bias Easy™ 1200 measures the current in the power tubes of your amp.   Designed for amplifiers with 4 power tubes, such as 100 watt Marshalls and the Fender Twin Reverb.   (May also be used on amps with only 2 power tubes).   Includes four 8-pin probes with gold plated pins and socket, power adapter and  operating instructions.  Fully assembled and ready to use.  For 8-pin power tubes such as 6L6, 6V6, 5881, 6550, EL34, KT88, KT66, KT100, etc.   Not for 7591 tubes.

The Bias Easy™ 1200 allows you to monitor the bias setting safely and easily. While adjusting the bias control pot of your amp, the Bias Easy™ 1200 shows the actual current flowing through each of the four power tubes.   A rotary switch on the meter allows you to check each tube for current flow.  This lets you set and evaluate the full reasonable biasing range your amp and tubes offer so that you may find the perfect setting.  Complete instructions are included.

The bias setting has a dramatic impact on the amp's tone, response, break-up and dynamic character.
Part #RBE-1200

$124.95


(TUBE NOT INCLUDED)

Click on photo for
larger view

Revisit™ PRE-AMP TUBE DAMPER RINGS.   Use two (or three) of these rings around a pre-amp tube to reduce noise and microphonics.  An economical alternative to more expensive tube dampers.   Will withstand high temperatures of pre-amp tubes, reusable when you change tubes.   Set of 6 rings - will equip either 2 or 3 tubes, depending on the number of rings you choose for each tube. Note: Tube shields will not fit over the damper rings, and must be removed from the tubes.   These dampers are NOT for 9-pin power tubes, such as the EL84 or 6BQ5. 
Part #PTD-6
$4.95
(Set of 6 rings)


Click on photo for
larger view
Fender PRE-AMP TUBE STABILIZER.  
Replacement high-temperature foam tube stabilizer for Fender™ Hot Rod Deluxe and Hot Rod Deville amps. This foam block slides over the first two preamp tubes. This genuine Fender™ replacement is made in the USA.
Part #ST-718
$14.95


Click on photo for
larger view
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL WITH 9-PIN TUBE SOCKET AND INTEGRAL TUBE SHIELD BASE .  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes.   9-Pin tube socket is made of sturdy Micalex.   Replacement for Fender™ and many other brands.  Holes in base spaced 1 1/8" apart.   Requires 3/4" hole in chassis.  Solder lugs for wire connection to tube socket. Shield, base and socket
Part #TS-370
$4.99  


Click on photo for
larger view
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL.  Includes new base, if needed.  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender™ and many other brands.  Holes in base spaced 1 1/8" apart.  Shield and base only - socket not included.
 
Part #TS-325S
$2.29  


Click on photo for
larger view
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL, SET OF 6.  Includes new bases, if needed.  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender™ and many other brands.  Holes in base spaced 1 1/8" apart.   This is a great kit to replaced all 6 of the tube shields in many Fender™ amps with 6 preamp tubes.  Shield and base only - socket not included.
 
Part #TS-325S-6
$12.95  


Click on photo for
larger view
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE FOR MATING WITH PREFORMED CHASSIS HOLE, ALUMINUM, 2" TALL, SPRING IN TOP OF SHIELD WHICH FITS OVER the TUBE.   Fits 12AX7A and similarly sized preamp tubes.  Comes with rubber gasket for sealing and noise damping with chassis.  Replacement for Marshall™ and some other brands. 
Part #TS-601
$2.79  


Click on photo for
larger view
TUBE RETAINER WITH SPRINGS, DESIGNED FOR 6L6 OR EL34 TUBES.   USED IN Marshall™ AND MANY OTHER AMPS. 
Part #TC-141
$3.49


Click on photo for
larger view
LARGE TUBE RETAINER WITH SPRINGS, DESIGNED FOR 6550 OR KT-88 TUBES.  

Part #TC-143
$3.49


Click on photo for
larger view
SMALL TUBE RETAINER WITH SPRINGS, DESIGNED FOR EL84 OR 6BQ5 TUBES.
A better way to support EL84 or 6BQ5 power tubes.   Top bracket has a hole for the glass nub at the top of the tube.   Mounts to the same screws that hold the tube socket.

Part #TR-148
$2.49


Click on photo for
larger view
TUBE RETAINER WITH SPRINGS, DESIGNED FOR 6V6, 5AR4, GZ34, 6SN7 TUBES.
Spring loaded retainer for 6V6 or smaller 5881 power tubes.   Also works with most 6SN7 preamp tubes and most 5AR4 or GZ34 rectifier tubes.   Mounts to the same screws that hold the tube socket.

Part #TR-149
$2.89


Click on photo for
larger view
TUBE RETAINER WITH GRIP TEETH, DESIGNED FOR OCTAL TUBES WITH PHENOLIC BASE SUCH AS 6L6 OR EL34.   Used in Fender™ and many other amps.     1 1/2" mounting centers.  Made by Belton.  Fender part number 099072500.
Part #TC-142
$2.25


Click on photo for
larger view
TUBE RETAINER FOR EL84 OR 6BQ5 TUBES.   2 inches between base and top bracket which fits around the "nub" at the top of the tube.   Will not fit all situations  - works best when the tube socket is recessed below the chassis about 1/4 inch.    1-1/8" mounting centers. 
Part #TR-144
$2.95


Click on photo for
larger view
TUBE RETAINER FOR 12AX7, 12AT7 TUBES.   1˝ inches between base and top bracket which fits around the "nub" at the top of the tube.   Will not fit all situations  - works best when the tube socket is exactly flush with the chassis.   1-1/8" mounting centers.
Part #TR-146
$2.95


Click on photo for
larger view
Fender™ Vintage Amp (60s Blackface and 70s Silverface) Power Tube Socket replacement kit.    For vintage Fender™ amps (NOT Reissues!) from the original blackface and silverface eras which have two power tubes (6L6 or 6V6).   Contains two phenolic 8-pin sockets, two "bear trap" retainers, four mounting screws, two 470 ohm screen grid resistors (Metal-Film Flameproof for safety), and two carbon composition 1500 ohm control grid resistors.   Princeton and Princeton Reverb do not need the resistors.   Perfect for Vibrolux Reverb, Vibroverb, Super Reverb, Deluxe Reverb, Pro Reverb, Bassman, Bandmaster Reverb, Tremolux, etc.
Part #FPTSK-2
$13.95


Click on photo for
larger view
Fender™ Vintage Amp (60s Blackface and 70s Silverface) Power Tube Socket replacement kit.    For vintage Fender™ amps (NOT Reissues!) from the original blackface and silverface eras which have four power tubes (6L6).   Contains four phenolic 8-pin sockets, four "bear trap" retainers, eight mounting screws, four 470 ohm screen grid resistors (Metal-Film Flameproof for safety), and four carbon composition 1500 ohm control grid resistors.   Perfect for Twin Reverb, Showman and Dual Showman, Quad Reverb, Bassman 100, etc.
Part #FPTSK-4
$26.95


Click on photo for
larger view
OCTAL TUBE KEYWAY, SET OF 2
If you have a cherished octal power tube or rectifier with a broken keyway, here is a great solution. By cleaning the remainder of the broken keyway from the tube base and properly installing this keyway replacement (a little dab of silicone sealant works great to hold it in place), your tube can safely be reinstalled into your equipment.   These great tube-savers are sold in sets of 2.   Note:  When using an adhesive to secure the keyway to the tube base, DO NOT use a water-based glue.   Silicone sealant (RTV) which is acryllic-based or butyl-based is fine.   Latex sealant or hot-glue is NOT.
Part #OTK8-2
$8.99
(for a set of 2 tube keyways)


Click on photo for
larger view
OCTAL TUBE BASE, SOLD INDIVIDUALLY
Octal tube bases are used to construct tube socket savers, solid-state rectifiers, bias probes, etc.   8-pin plug with room inside the base for circuitry and wiring.  Sold individually.
Part #OTB-100

$3.99 ea


Click on photo for
larger view
TUBE SOCKET, OCTAL 8-PIN, commonly used with the Octal Tube Base to build bias probes, tube socket savers, tube extenders, etc.   This socket has no mounting bracket.
Part #TS-8-810
$4.40  


Click on photo for
larger view
PHENOLIC TUBE SOCKET FOR OCTAL TUBES.  EXACT REPLACEMENT FOR VINTAGE FENDER, VINTAGE Marshall™ (including the JCM900 Series), and many others.    Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes.   For 1" to 1 1/8" hole.  Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/2" apart.  Unlike some phenolic tube sockets on the market, this one fits the 1" hole found in most vintage Fenders.  
Part #TS-8-600
$4.50


Click on photo for larger view

CERAMIC 8-PIN PC MOUNT OUTPUT TUBE OR RECTIFIER TUBE SOCKET, crimped bracket, bottom mount 1 1/4", top mount 1" to 1 1/8", 1 1/2" mounting centers, 1" to 1 1/4" chassis hole.  Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes. Used in Peavey, Fender and other brands where the tube socket is mounted to a PC board.   Click here for additional specs.   Fender part number 0057238000 or 0029343000.
Part #TS-8-807

$3.95


Click on photo for larger view

CERAMIC 8-PIN WIRED OUTPUT TUBE OR RECTIFIER TUBE SOCKET, crimped bracket, bottom mount 1 1/4", top mount 1" to 1 1/8", 1 1/2" mounting centers, 1" to 1 1/4" chassis hole.  Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes.  Click here for additional specs.   Fender part number 0990724000, or 023580.
Part #TS-8-807W

$3.95

 

Click on photo for
larger view

Socket - Belton, Micalex, 8 Pin, Octal PC Mount, Long Lead Micalex, PC mount, long leads (Belton) - MB/MT. 1 ˝" mounting centers 1-3/16" chassis hole. Applicable for use with all types of electric and electronic equipment using vacuum tubes.  Paddle saddle mounting, easy mount with the saddle of extruded screw hole.   Phosphorous bronze pin terminal with tin plating, glass fiber field PPS Insulating material
Part # TS-8-209

$3.50

 

Click on photo for
larger view

Socket - Belton, Micalex, 8 Pin, Octal PC Mount, Solder Lugs   Micalex construction, solder lugs for attaching wire.  1 ˝" mounting centers 1-3/16" chassis hole. Applicable for use with all types of electric and electronic equipment using vacuum tubes.  Paddle saddle mounting, easy mount with the saddle of extruded screw hole.   Phosphorous bronze pin terminal with tin plating, glass fiber field PPS Insulating material.   Used by a number of amp manufacturers.
Part # TS-8-209W

$3.95


Click on photo for larger view

Belton 8 pin socket, Micalex, for PC board mounting  Belton 8 Pin Octal Auto Wave Solder Micalex Socket. Very high quality. This is a specially designed socket that mounts under the PCB.  Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes.  Click here for additional specs.
Part #TS-8-BEL

$3.99

PC MOUNT TYPE
Click on photo for
larger view

PC MOUNT MICALEX TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  INCLUDES INTEGRAL BASE FOR TWIST-LOCK TUBE SHIELD.   FOR USE ON PC BOARD AMPS!       Fits 12AX7, 12AU7, 12AT7, etc.   Sturdy Micalex construction, for 3/4"  hole.  PC Pins.   Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/8" apart.   Designed to work with the TS-325S tube shield, or vintage Fender tube shields. 
Part #TS-9-700-PC
$2.69


Click on photo for
larger view
FENDER STYLE MICALEX TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  INCLUDES INTEGRAL BASE FOR TWIST-LOCK TUBE SHIELD.        Fits 12AX7, 12AU7, 12AT7, etc.   Sturdy Micalex construction, for 3/4"  hole.  Solder tabs for wire connections.   Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/8" apart.   Designed to work with the TS-325S tube shield, or vintage Fender tube shields.   Used in Fender vintage Blonde, Brownface, Blackface, Silverface and some early Rivera designs.   Also applicable to early Marshall designs.  Fender part number 0023606049.
Part #TS-9-700
$4.49


Click on photo for
larger view
6-PACK OF FENDER STYLE MICALEX TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  INCLUDES INTEGRAL BASE FOR TWIST-LOCK TUBE SHIELD.      Fits 12AX7, 12AU7, 12AT7, etc.   Sturdy Micalex construction, for 3/4"  hole.  Solder tabs for wire connections.   Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/8" apart.   Designed to work with the TS-325S tube shield, or vintage Fender tube shields.   Used in Fender vintage Blonde, Brownface, Blackface, Silverface and some early Rivera designs.   Also applicable to early Marshall designs.   Pack of 6 tube sockets.  Mounting screws not included - recommend the SC-410-6 screws (2 packs of 6 screws needed for 6 tube sockets).  It is also possible to use 1/8 inch pop rivets to mount these sockets.  Replaces Fender part number 0023606049.
Part #TS-9-700-6
$25.99
(for 6 sockets)


Click on photo for
larger view
TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  EXACT REPLACEMENT FOR MANY MAKES AND MODELS OF AMPS WITH HAND-WIRED TUBE SOCKETS.      Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.   For 3/4"  hole.  Bottom mounting (mounted from the inside of the chassis), mounting holes spaced 1 1/8" apart.   Designed to work with the TR-144 or TR-146 tube retainers, or the TS-325S tube shield.
Part #TS-9-601
$2.49


Click on photo for
larger view
TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  EXACT REPLACEMENT FOR MANY MAKES AND MODELS OF AMPS WITH HAND-WIRED TUBE SOCKETS.      Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.   For 3/4"  hole.  Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/8" apart.   Designed to work with the TR-144 or TR-146 tube retainers, or the TS-325S tube shield.
Part #TS-9-610
$2.49


Click on photo for
larger view
9 pin Belton Micalex socket for PC board mounting.   Mounts under the PC board.  Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.   Used in Marshall™ , Peavey™ and other brands.  Click here for additional specs.
Part #TS-9-BEL
$2.79


Click on photo for
larger view
TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  PC MOUNT, CERAMIC.    9 pin ceramic PC mount socket, stand-off mounting, 0.82" diameter, 3/8" tall above PC board.   Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.   
Part #TS-9-223
$2.49


Click on photo for
larger view
TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  PC MOUNT, MICALEX.    9 pin ceramic PC mount socket, stand-off mounting, 3/4" diameter, 3/4" tail diameter.  For bottom mounting (mounted from the inside of the chassis, below the chassis hole).   Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.    Micalex replacement for the tube sockets in the Fender™ Blues Junior, Pro Junior, and the Fender™ Hot Rod Deluxe/Deville and Blues Deluxe/Deville.   Fender part number 0029167049.  Also used in Gibson™ Goldtone series amplifiers.
Part #TS-9-620
$2.69


Click on photo for
larger view
3-PACK, TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  PC MOUNT, MICALEX.    9 pin ceramic PC mount socket, stand-off mounting, 3/4" diameter, 3/4" tail diameter.  For bottom mounting (mounted from the inside of the chassis, below the chassis hole).   Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.  Fender part number 0029167049.    This 3-pack replaces all of the sockets for the 12AX7 preamp tubes in the Fender™ Blues Junior, Hot Rod Deluxe/Deville and Blues Deluxe/Deville.  Also used in Gibson™ Goldtone series amplifiers.
Part #TS-9-620-3
$7.79
(for a 3-pack of tube sockets)


Click on photo for
larger view
5-PACK, TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  PC MOUNT, MICALEX.    9 pin ceramic PC mount socket, stand-off mounting, 3/4" diameter, 3/4" tail diameter.  For bottom mounting (mounted from the inside of the chassis, below the chassis hole).   Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.    Fender part number 0029167049.    This 5-pack replaces all 5 tube sockets in the Fender™ Blues Junior.  Also used in Gibson™ Goldtone series amplifiers.
Part #TS-9-620-5
$12.49
(for a 5-pack of tube sockets)


Click on photo for
larger view
10-PACK, TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  PC MOUNT, MICALEX.    9 pin ceramic PC mount socket, stand-off mounting, 3/4" diameter, 3/4" tail diameter.  For bottom mounting (mounted from the inside of the chassis, below the chassis hole).   Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.    Fender part number 0029167049.    Used in the Fender™ Blues Junior, and the Fender™ Hot Rod Deluxe/Deville and Blues Deluxe/Deville.  Used in Gibson™ Goldtone series amplifiers.
Part #TS-9-620-10
$23.90
(for a 10-pack of tube sockets)


Click on photo for
larger view
TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  PC MOUNT, CERAMIC.    9 pin ceramic PC mount socket, stand-off mounting, 3/4" diameter, 3/4" tail diameter.  For bottom mounting (mounted from the inside of the chassis, below the chassis hole).   Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.    Ceramic replacement for Gibson™ Goldtone series amplifiers.  Ceramic replacement for the tube sockets in the Fender™ Blues Junior, and the Fender™ Hot Rod Deluxe/Deville and Blues Deluxe/Deville.   Also makes an excellent replacement for the single tube socket in the Marshall ValveState models.
Part #TS-9-217
$2.69


Click on photo for
larger view

Fender™ SELF-TAPPING SCREWS
Used in vintage Fender™ blackface and silverface amps for a variety of tasks.   Used to attach capacitor pans, tube sockets, transformers on smaller amps, chokes, etc.   Pack of 12 screws.  Replaces Fender™ part number 029913.
Part #SC-410-12
$3.50
(for a pack of 12 screws)
 


Copyright ©2024 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
  WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov