Screws, Nuts, Washers &
Chassis Straps


 

Hardware

   

Click on photo for
larger view
CUP WASHER, BLACK METAL, PACK OF 10.  Used with #8 Black screws, on amps and speaker cabinets.
Part #BCW-10
$1.69
(pack of 10)
 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, SMALL, SET OF 4.  OD 3/8", ID 5/32".   Typically found on the back panel of some Fender™ Blonde/Brown era amps, and some Blackface vintage amps.   Set of 4 washers.  Fender™ part number 0037215049.    OUTSIDE EDGE OF WASHER IS BARELY LARGER THAN the HEAD OF the Fender™ BACK PANEL SCREWS.  
Part #CW-401-4
$0.99
(for a set of 4 washers)
 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, SMALL, SET OF 8.  OD 3/8", ID 5/32".   Typically found on the back panel of some Fender™ Blonde/Brown era amps, and some Blackface vintage amps.   Set of 8 washers.  Fender™ part number 0037215049.   OUTSIDE EDGE OF WASHER IS BARELY LARGER THAN the HEAD OF the Fender™ BACK PANEL SCREWS.  
Part #CW-401-8
$1.79
(for a set of 8 washers)
 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, MEDIUM, SET OF 4.  OD 7/16", ID 3/16"  Typically found on the back panel of some Fender™ Blackface/Silverface vintage amps and the reissues of those amps.   Larger than the CW-401-4 - Fender™ was not consistent in which washers they used on back panels over the years.  Set of 4 washers.
Part #CW-501-4
$0.99
(for a set of 4 washers)
 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, MEDIUM, SET OF 8.  OD 7/16", ID 3/16"  Typically found on the back panel of some Fender™ Blackface/Silverface vintage amps and the reissues of those amps.   Larger than the CW-401-4 / CW-401-8 sets - Fender™ was not consistent in which washers they used on back panels over the years.  Set of 8 washers.
Part #CW-501-8
$1.79
(for a set of 8 washers)
 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 4.  OD 1/2", ID 3/16"  Typically found on larger combo amp cabinets and 4x12 cabinets, such as Marshall™ .   Set of 4 washers.
Part #CW-400-4
$0.99
(for a set of 4 washers)
 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 8.  OD 1/2", ID 3/16"  Typically found on larger combo amp cabinets and 4x12 cabinets, such as Marshall™ .   Set of 8 washers.
Part #CW-400-8
$1.95
(for a set of 8 washers)
 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 17.  OD 1/2", ID 3/16"  Typically found on larger combo amp cabinets and 4x12 cabinets, such as Marshall™ .   Set of 17 washers.  Some of the larger Marshall 4x12 cabinets, such as certain model 1960 cabinets, have 17 screws and washers in the back panel.
Part #CW-400-17
$3.79
(for a set of 17 washers)
 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 28.  OD 1/2", ID 3/16"  Complete set of 28 stainless steel cup washers for the vintage Fender Bassman 2x12 and Bandmaster 2x12 cabinets.    Set of 28 washers.  Use with the SC-400-28 set of screws.
Part #CW-400-28
$5.59
(for a set of 28 washers)
 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 36.  OD 1/2", ID 3/16"  Complete set of 36 stainless steel cup washers for the vintage Fender Bassman 2x15 cabinets.    Set of 36 washers.  Use with the SC-400-36 set of screws.
Part #CW-400-36
$6.89
(for a set of 36 washers)
 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, EXTRA LARGE.  OD 9/16", ID 1/4"   Typically found on larger 4x12 cabinets, and other pro audio speaker cabinet applications.  Set of 4 washers.
Part #CW-502-4
$0.99
(for a set of 4 washers)
 


Click on photo for
larger view
SAVE WITH MULTIPACK!  JNUT-38 JACK NUT AND WASHER, METAL, SWITCHCRAFT, SET OF 6
Genuine Switchcraft™ nut and washer set for the blackface/silverface Fender™ bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8" bushing (found on original vintage Fender™ blackface and silverface), as well as Peavey™ and Switchcraft™ 1/4" jacks.  Does NOT fit the 24mm Marshall™ pots.   Set of 6 washers and 6 nuts. 
Part #JNUT-38-6
$4.50
(Set of 6 washers and 6 nuts)
 

JACK NUT AND WASHER, METAL, SWITCHCRAFT
Genuine Switchcraft™ nut and washer set for the blackface/silverface Fender™ bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8" bushing (found on original vintage Fender™ blackface and silverface), as well as Peavey™ and Switchcraft™ 1/4" jacks.  Does NOT fit the 24mm Marshall™ pots.  
Part #JNUT-38
$0.89
(Set of 1 washer and 1 nut)
 


Click on photo for
larger view.   Jack is in the picture to demonstrate how the washers are installed - jack is NOT included with the washers.
INSULATING SHOULDER WASHER, FIBER
Pair of fiber insulating shoulder washers for Switchcraft jacks with metal bushings.   Used to mount standard jacks in a 1/2" diameter chassis hole, while insulating the metal bushing (ground) of the jack from the chassis.   ID 3/8", OD 1/2".  Works great when replacing isolated plastic jacks with a more durable metal jack, which is frequently done on the input jacks of the Fender™ Hot Rod Deville/Deluxe and Blues Deville/Deluxe.   Two washers are used on each jack, and the "shoulders" are placed facing each other through the chassis.   The washers not only isolate the ground of the jack electrically for noise reduction, but also stabilize the jack in the 1/2" diameter hole.   Jack shown in picture NOT included.   Works well with the Switchcraft J-11, J-L11, J-12A, J-L12A, J-12B, J-L12B, J-13, J-13A, J-112APC, J-112BX, J-114BX, J-521 and J-524 jacks.
Part #ISW-3069
$0.49
(For a pair of washers.  Each jack needs two washers.)
 


Click on photo for
larger view
WASHER, FOR BRITISH STYLE (CLIFF) JACKS.
This washer goes behind the faceplate on British style plastic nut and chrome nut jacks to provide proper spacing.   Jacks come with the washers included, but the washers are easily lost.  Without the washers, the jacks will not fit properly.

Part #W-583
$0.18
for each washer.
(Jacks not included).
 


Click on photo for
larger view
Mesa/Boogie™ Nickel Chassis Strap - Large (6"), bright nickel finish. Single chassis strap, no screws. Screw spacing is 5.31 inches center-to-center, strap length is 6 inches end-to-end.  Original Mesa/Boogie part number 407520.   Sold individually - ordering quantity of 1 delivers 1 strap.
Part #MBCS-6
$8.50

(Sold individually - One chassis strap, screws NOT included)
 



Click on photo for
larger view
Mesa/Boogie™ Stainless Steel Screw - 4 inches long, 10-24 thread.   Used with the MBCS-6 chassis straps.   Original Mesa/Boogie part number 302190.  Sold individually - ordering quantity of 1 delivers 1 screw.    Each amplifier requires a total of 4 screws. 
Part #MBCB
$1.39

(Sold individually - Each amp uses 4 screws)
 



Click on photo for
larger view
Fender™ Nickel Chassis Straps - Large (5") for Twin, Bassman, Super, Showman, Vibro-King, Pro, Pro Reverb, Prosonic, etc.  Includes 2 straps, no screws or nuts.  Screw spacing is 5 inches center-to-center, strap length is 5 5/8" end-to-end.
Part #FCS-5-2
$7.95
(Two chassis straps, screws and nuts NOT included)
 



Click on photo for
larger view
Fender™ Nickel Chassis Straps - Medium (4") For Deluxe, Vibrolux, etc.   Includes 2 chassis straps, no screws or nuts.  Screw spacing is 4 inches center-to-center, strap length is 4 5/8" end-to-end.
Part #FCS-4-2
$7.49
(Two 4 in. chassis straps, screws and nuts NOT included)
 


Click on photo for
larger view
Fender™ Nickel Chassis Straps - Small (3")  For Champ, Music Master Bass, etc.  Includes 2 chassis straps, no screws or nuts.  Screw spacing is 3 inches center-to-center, strap length is 3 5/8" end-to-end.
Part #FCS-3-2
$6.99
(Two 3 in. chassis straps, screws and nuts NOT included)
 


Click on photo for
larger view
Fender™ Chassis Bolt Set - Works with all Fender Nickel or Revisit Chassis Straps for Blackface,  Silverface through 1975, and reissued Blackface models.   Includes 4 bolts and 4 matching nuts with integral lock washers.  Fender part number 0022236049.
Part #FCB-4
$5.95
(
4 bolts, 4 nuts - complete set for one amp)
 


Click on photo for
larger view
Fender™ Chassis Bolt Set - Works with all Fender™ Nickel Chassis Straps on 1976+ and early 80s (ultralinear) Silverface models.   Includes 4 bolts 8-32, 1 1/2" long.  Stainless steel.
Part #FNCB-4
$1.95
(
4 bolts - complete set for one amp)
 


Click on photo for
larger view

Fender™ STAINLESS STEEL BACK-PANEL SCREWS
Pack of 6 stainless steel back panel screws suitable for Fender™ reissue "Tweed" series amps. Fits the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, Blues Junior and Blues Deville, and 59 Bassman reissue.   3/4" long, 10-32 thread.    Fender™ Original Part number 0015990049.   Pack of 6 screws.   Made of stainless steel, for longer life and no worries about rust or oxidation. These screws are not nickel-plated.
Part #FBP-6
$2.99
(for a pack of 6 screws)


Click on photo for
larger view

Fender™ STYLE STAINLESS STEEL CHASSIS MOUNTING SCREWS
Pack of 6 stainless steel chassis mounting screws suitable for Fender™ reissue "Tweed" series amps.   Mounts the chassis to the cabinet on top as well as the sides of the cabinet.  Fits the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, Blues Junior, Pro Junior, and Blues Deville, 59 Bassman reissue. 1 1/2" long, 10-32 thread.    Replacement for  Fender™ Part number 0036619049.   Pack of 6 screws.   Made of stainless steel, for longer life and no worries about rust or oxidation. Note:  These screws are not nickel-plated.   For original Fender screws, see the FGCM-6 set.
Part #FCM-6
$2.99
(for a pack of 6 screws)


Click on photo for
larger view

Genuine Fender™ NICKEL-PLATED STEEL CHASSIS MOUNTING SCREWS
Pack of 6 nickel-plated steel chassis mounting screws suitable for Fender™ reissue "Tweed" series amps.   Mounts the chassis to the cabinet on top as well as the sides of the cabinet.  Fits the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, Blues Junior, Pro Junior, and Blues Deville, 59 Bassman reissue. 1 1/2" long, 10-32 thread.   Pack of 6 screws.   10-32 X 1-1/2 TH PHS Nickel-Plated Screws.   Genuine Fender™ Original Part number 0036619049.
Part #FGCM-6
$5.95
(for a pack of 6 screws)


Click on photo for
larger view

Fender™ STYLE ZINC-PLATED STEEL CABINET WASHERS
Pack of 6 zinc-plated steel cabinet washers suitable for Fender™ reissue "Tweed" series amps.  Used on the chassis mounting screws as well as the back-panel mounting screws.  Fits the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, Blues Junior, Pro Junior, and Blues Deville, 59 Bassman reissue.  Pack of 6 washers.   A replacement for Fender™ Part number 0022327049.
Part #FCW-6
$0.50
(for a pack of 6 washers)


Click on photo for
larger view

Fender™ STYLE STAINLESS STEEL CHASSIS MOUNTING SCREWS WITH KEPS NUTS
Pack of 6 stainless steel chassis mounting screws and matching KEPS nuts for Fender™ original "Tweed" series amps.   Mounts the chassis to the cabinet on top as well as the sides of the cabinet.  Fits the Fender™ original Tweed amps from the 1950s:   Tweed Vibrolux, Tweed Twin, Tweed Tremolux, Tweed Super, Tweed Pro, Tweed Princeton, Tweed Harvard, Tweed Deluxe, Tweed Champ, and Tweed Bassman.   1 1/2" long, 10-32 thread.  Replacement for Fender™ Original Part number 0992095000.  Pack of 6 screws with 6 nuts.   Screws made of stainless steel, for longer life and no worries about rust or oxidation. These screws are not nickel-plated.
Part #FVCM-6
$3.99
(for a pack of 6 screws and 6 nuts)


Click on photo for
larger view

Genuine Fender™ NICKEL-PLATED STEEL CHASSIS MOUNTING SCREWS WITH KEPS NUTS
Pack of 6 nickel-plated steel chassis mounting screws and matching zinc-plated KEPS nuts for Fender™ original "Tweed" series amps.   Mounts the chassis to the cabinet on top as well as the sides of the cabinet.  Fits the Fender™ original Tweed amps from the 1950s:   Tweed Vibrolux, Tweed Twin, Tweed Tremolux, Tweed Super, Tweed Pro, Tweed Princeton, Tweed Harvard, Tweed Deluxe, Tweed Champ, and Tweed Bassman.   1 1/2" long, 10-32 thread.  Pack of 6 screws with 6 nuts.  10-32 X 1-1/2 TH PHS Nickel-Plated Screws. Fender™ Original Part number 0992095000. 
Part #FGVC-6
$6.95
(for a pack of 6 screws and 6 nuts)


Click on photo for
larger view

Fender™ "DOGBONE" HANDLE SCREWS
Pack of 4 stainless steel "Dogbone" handle screws for Fender™ style FAH-328 and FAH-329 handles.    8-32 thread.  Fits the handle on the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, and Blues Deville, as well as other Fender™ amps of similar design.  Also works with Hiwatt or Vox™ handles and other British design amp handles. 
Part #SC-402
$1.59
(for a pack of 4 screws)
 


Click on photo for
larger view

Fender™ VINTAGE HANDLE SCREWS
Pack of 2 stainless steel handle screws for Fender™ style FAH-332, FAH-261 handle.   1" Long, 10-32 threads.   Designed to work with a 10-32 T-Nut, in cabinet wood of 3/4" or less.    Will not work with external nut - must be a T-Nut.   Will not work with cabinet wood thicker than 3/4".  See Data Sheet here
Part #SC-403
$0.99
(for a pack of 2 screws)
 


Click on photo for
larger view

10-32 THREAD HANDLE SCREWS
Pack of 4 stainless steel handle screws for handles which require 4 screws.   1" Long, 10-32 threads.   Designed to work with a 10-32 T-Nut, in cabinet wood of 3/4" or less.    Will not work with external nut - must be a T-Nut.   Will not work with cabinet wood thicker than 3/4".  See Data Sheet here
Part #SC-403-4
$1.95
(for a pack of 4 screws)
 


Click on photo for
larger view

Fender™ EXTRA LONG VINTAGE HANDLE SCREWS
Pack of 2 stainless steel extra long handle screws for Fender™ style FAH-332, FAH-261 handle.   Used for vintage Fender™ style strap handles used on speaker cabinets, such as Bandmaster, Bassman, Showman, and Blonde or Blackface Tremolux.  1-1/4" Long, 10-32 threads.   Designed to work with a 10-32 T-Nut, in cabinet wood of 1-1/8" or less.    Will not work with external nut - must be a T-Nut.   Will not work with cabinet wood thicker than 1-1/8".  See Data Sheet here
Part #SC-403A
$0.99
(for a pack of 2 screws)
 


Click on photo for
larger view

Fender™ SELF-TAPPING SCREWS
Used in vintage Fender™ blackface and silverface amps for a variety of tasks.   Used to attach capacitor pans, tube sockets, transformers on smaller amps, chokes, etc.   Pack of 12 screws.  Replaces Fender™ part number 029913.
Part #SC-410-12
$3.50
(for a pack of 12 screws)
 


Click on photo for
larger view
Peavey™ Stainless Steel Screw - 4 inches long, 10-24 thread.  Used on a variety of vintage Peavey amps which had chassis straps on top of the amp cabinet. Sold individually - ordering quantity of 1 delivers 1 screw.    Each amplifier requires a total of 4 screws. 
Part #PBCB
$1.39

(Sold individually - Each amp uses 4 screws)
 



Click on photo for
 larger view
Black Oxide Stainless Steel Pan Head 10-32 x 3/4" Speaker Mounting Screws, Rack Mount Screws
Set of 4 screws.   Used to mount speakers, back panels, etc in a variety of amplifiers.    10-32 thread, 3/4" long with pan head.  May also be used as rack-mount screws.   Stainless steel, will not rust.

Part #SC-202
$1.59
(for a set of 4 screws)


Click on photo for
 larger view
Black Oxide Stainless Steel Pan Head 10-32 x 1" Speaker Mounting Screws, Rack Mount Screws
Set of 4 screws.   Used to mount speakers, back panels, etc in a variety of amplifiers.    10-32 thread, 1" long with pan head.  May also be used as rack-mount screws.   Stainless steel, will not rust.

Part #SC-202A
$1.79
(for a set of 4 screws)


Click on photo for
 larger view
Black Oxide Stainless Steel Pan Head 4-40 x 5/16" Screws and Nuts, Set of 4
Set of 4 small black screws with matching nuts.  Stainless steel with black oxide finish.  Used in a variety of applications on both guitars and amplifiers.
Part #SCBN-440
$1.69
(for a set of 4 screws with nuts)



Click on photo for
 larger view
Black Logo Mounting Screws
Set of 4 logo mounting screws.   These are #5 x 7/16" black oxide screws, set of 4.    Fit the AL-921 Ampeg logo, and the Fender FAL-912 logo.
Part #LS-504
$0.99
(for a set of 4 screws)


Click on photo for
larger view

Fender™ Style Stainless Steel Corner Screws, Set of 8
Oval-head Phillips corner screws for counter-sunk amp corners, such as the FVC-2L and FVC-3 Fender™ corners.   3/4 inches long, Phillips head, stainless steel for long rust-free life.  
Set of 8 screws, for four FVC-2L corners.

Part #SC-406-8

$2.99
(for a pack of 8 screws)
 


Click on photo for
larger view

Fender™ Style Stainless Steel Corner Screws, Set of 12
Oval-head Phillips corner screws for counter-sunk amp corners, such as the FVC-2L and FVC-3 Fender™ corners.   3/4 inches long, Phillips head, stainless steel for long rust-free life.  
Set of 12 screws, for four FVC-3 corners.

Part #SC-406-12

$4.29
(for a pack of 12 screws)
 


Click on photo for
larger view
Black Oval-Head Corner Screws, Set of 8
Black oval-head Phillips corner screws for counter-sunk amp corners.   Works with Vox black plastic corners, and Fender style black metal corners with recessed screw holes.   #6 x 3/4 inches long, Phillips head, black oxide.  Screws are beveled under the head for use in countersunk holes.   Length measured from the edge of the head to tip of the screw.  
Set of 8 screws.
Part #SC-411-8
$1.50
(For a set of 8 black oval-head Phillips screws)



Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS (SET OF 4)  FOR OPEN BACK CABINETS (such as Fender™ Blonde, Brown, Blackface and Silverface Series).   Set of 4 screws, stainless steel, 1 1/4 inches long, Phillips, oval head.  This set of four screws fits either the top or bottom rear panels on Fender™ combo amps from the 60s and 70s, and recent reissues of those BF and SF amps.   Use with either the CW-401 or CW-501 cup washers.
Part #SC-401-4
$0.99
(for a pack of 4 screws)
 



Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS (SET OF 8) FOR OPEN BACK CABINETS (such as Fender™ Blonde, Brown, Blackface and Silverface Series.     Set of 8 screws, stainless steel, 1 1/4 inches long, Phillips, oval head.   This set of eight screws fits both the top and bottom rear panels on Fender™ combo amps from the 60s and 70s, and recent reissues of those BF and SF amps.  Set of 8 completely replaces all of the screws on the two back panels.  Use with either the CW-401 or CW-501 cup washers.
Part #SC-401-8
$1.79
(for a pack of 8 screws)
 



Click on photo for
larger view
SATIN BLACK BACK PANEL STAINLESS STEEL SCREWS (SET OF 4)  FOR OPEN BACK CABINETS (such as Fender™  Blonde, Brown, Blackface and Silverface Series.     Set of 4 screws, satin black stainless steel, 1 1/4 inches long, Phillips, oval head.  This set of four screws fits either the top or bottom rear panels on Fender™ combo amps from the 60s and 70s, and recent reissues of those BF and SF May be used with the BCW-10 cup washers.   See data sheet
Part #SC-405-4
$0.99
(for a pack of 4 screws)
 



Click on photo for
larger view
SATIN BLACK BACK PANEL STAINLESS STEEL SCREWS (SET OF 8) FOR OPEN BACK CABINETS (such as Fender™ Blonde, Brown, Blackface and Silverface Series).     Set of 8 screws, satin black stainless steel, 1 1/4 inches long, Phillips, oval head.   This set of eight screws fits both the top and bottom rear panels on Fender™ combo amps from the 60s and 70s, and recent reissues of those BF and SF amps.  Set of 8 completely replaces all of the screws on the two back panels.  May be used with the BCW-10 cup washers.  See data sheet
Part #SC-405-8
$1.89
(for a pack of 8 screws)
 


Click on photo for
larger view
CUP WASHER, BLACK METAL, PACK OF 10.  Used with #8 Black screws, on amps and speaker cabinets.
Part #BCW-10
$1.69
(pack of 10)
 



Click on photo for
larger view
SPEAKER BAFFLE MOUNTING STAINLESS STEEL SCREWS AND WASHERS (SET OF 6) FOR Fender™ Blackface and Silverface Series.    Set of 6 screws with oval Philips heads, stainless steel #8, 1 3/4 inches long, and matching set of 6 stainless steel cup washers.   This set of six screws w/washers fastens the speaker baffle board to the cabinet on Fender™ blonde, brownface, blackface and silverface combo amps from the 60s and 70s, and recent reissues of those BF and SF amps.   Replaces Fender part number 011678.
Part #SC-407-6
$2.29
(for a pack of 6 screws and washers)
 



Click on photo for
larger view
Fender™ GRILLE SCREWS (SET OF 4) FOR BROWN, BLONDE, BLACKFACE AND SILVERFACE HEADS.  Set of 4 screws, Stainless Steel, 1 3/4" long, Phillips, oval head, with matching cup washers. Fits all Fender™ vintage heads such as Bassman, Bandmaster, Showman, Dual Showman, Tremolux,etc and holds the grille to the front of the cabinet.
Part #FGS-4
$1.49
(for a pack of 4 screws and 4 washers)
 



Click on photo for
larger view
SPEAKER BAFFLE MOUNTING 4 COPPER SCREWS AND STAINLESS STEEL KEPS NUTS (SET OF 4) FOR Fender™ TWEED AMPS.   Set of 4 screws, copper 6-32, 1 1/2 inches long, Phillips and matching 6-32 Keps Nuts with integral washers.   This set of four copper screws connects the speaker baffle board to the cabinet on Fender™ tweed combo amps from the 50s, as well as recent reissue tweed amps such as the Hot Rod Deluxe and 59 Bassman Reissue.    Replaces Fender part number 036618 or 0036618049.   For amps which require additional baffle screws, see the individual screw/nut part number SC-415, below.
Part #SC-415-4
$3.99
(for a pack of 4 screws and 4 nuts)



Click on photo for
larger view
SPEAKER BAFFLE MOUNTING COPPER SCREW AND STAINLESS STEEL KEPS NUT FOR Fender™ TWEED AMPS.  Individual screw, copper 6-32, 1 1/2 inches long, Phillips and matching 6-32 Keps Nut with integral washer.   These screws connect the speaker baffle board to the cabinet on Fender™ tweed combo amps from the 50s, as well as recent reissue tweed amps such as the Hot Rod Deluxe and 59 Bassman Reissue.    Replaces Fender part number 036618 or 0036618049.
Part #SC-415
$1.09
(for a single screw with nut)


Set of 4 screws shown.  Set of 5 screws also available.

Click on photo for
larger view

SPEAKER BAFFLE MOUNTING STAINLESS STEEL SCREWS AND STAINLESS STEEL KEPS NUTS (SETS OF 4 OR 5) FOR Fender™ BLUES DELUXE, BLUES DEVILLE, BLUES JUNIOR III, HOT ROD DELUXE OR HOT ROD DEVILLE AMPS WITH BLACK TOLEX.   Sets of either 4 or 5 screws, stainless steel 6-32, 1 1/2 inches long, flat stainless washers, Phillips and matching 6-32 Keps Nuts with integral washers.   This set of four nickel style screws connects the speaker baffle board to the cabinet on Fender™ amps.   Blues Junior III needs the 4-screw set, other larger amps with black tolex need the 5-screw set.   Replaces Fender part number 050858 or 0050858000.   For amps covered in Tweed Tolex, see the SC-415 screws.
Part #SC-414-X
4-screw set:
$2.79

5-screw set:
$3.29
Select Option:


Quantity:


ORIGINAL Fender™ THUMBSCREWS  Fender™ piggyback thumbscrews, holds head to cabinet on Showman, Bandmaster, Tremolux, Tone Master™ 212, Super-Sonic™ 212 and Super-Sonic 60 speaker enclosures and other head/cabinet sets. Heavy nickel plated steel, heavy knurling on knob. Set Of Two. Genuine Fender™ part number 0990720000.
Part #TS-251
$12.95
(Set of 2 Thumbscrews)
 


Fender™ TILT-BACK LEG SCREWS AND CAPTIVE NUTS
Pack of 2 stainless steel tilt-back leg screws, 1-1/2 inches long, along with hex nuts with special nylon inserts.   Used on tilt-back legs of larger Fender combo amps and speaker cabinets.  Replaces Fender part numbers 021998 and 022277.
Part #SCW-403T-2
$1.79
(for a pack of 2 screws and
2 nuts)
 


Fender™ TILT-BACK LEG STOP SCREWS
Pack of 2 stainless steel tilt-back leg stop screws, 3/4 inches long.   Used on the tilt-back legs stops of larger Fender combo amps and speaker cabinets.
Part #SC-506-2
$0.99
(for a pack of 2 screws)
 



Click on photo for
larger view
#8 BACK PANEL STAINLESS STEEL SCREWS (SET OF 4) FOR OPEN BACK CABINETS.  Set of 4 screws, Stainless Steel, #8, 1 1/4" long, Phillips, oval head.   Used with the CW-400 cup washers.    These screws are larger in diameter than the typical Fender back panel screws, but fit a number of other combo amps with open-back cabinets.
Part #
SC-2265-4
$0.89
(for a pack of 8 screws)
 



Click on photo for
larger view
#8 BACK PANEL STAINLESS STEEL SCREWS (SET OF 8) FOR OPEN BACK CABINETS.  Set of 8 screws, Stainless Steel, #8, 1 1/4" long, Phillips, oval head.   Used with the CW-400 cup washers.    These screws are larger in diameter than the typical Fender back panel screws, but fit a number of other combo amps with open-back cabinets.
Part #
SC-2265-8
$1.59
(for a pack of 8 screws)
 



Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS (SET OF 8) FOR CLOSED BACK CABINETS (SUCH AS Marshall™, Fender™ Bassman, Bandmaster, etc ).  Set of 8 screws, Stainless Steel, 1 3/4" long, Phillips, oval head.   Use with the CW-400-8 washers.
Part #
SC-400-8
$1.99
(for a pack of 8 screws)
 



Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS (SET OF 17) FOR CLOSED BACK CABINETS (SUCH AS Marshall™).  Set of 17 screws, Stainless Steel, 1 3/4" long, Phillips, oval head.   Use with the CW-400-17.   A set of 17 screws completely replaces all of the screws on most Marshall™ 4x12 cabinets, including the 1960 models.
Part #
SC-400-17
$3.89
(for a pack of 17 screws)

 



Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS (SET OF 28) FOR CLOSED BACK CABINETS (SUCH AS Fender™ BASSMAN 2x12, BANDMASTER 2x12, etc).  Set of 28 #8 screws, Stainless Steel, 1 3/4" long, Phillips, oval head.   Use with  the CW-400-28 cup washers.   A set of 28 screws completely replaces all of the screws on most vintage Bassman™ 2x12 and Bandmaster™ 2x12 cabinets
Part #
SC-400-28
$5.69
(for a pack of 28 screws)

 



Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS (SET OF 28) FOR CLOSED BACK CABINETS (SUCH AS Fender™ BASSMAN 2x15).  Set of 36 #8 screws, Stainless Steel, 1 3/4" long, Phillips, oval head.   Use with  the CW-400-36 cup washers.   A set of 36 screws completely replaces all of the screws on most vintage Bassman™ 2x15 cabinets.
Part #
SC-400-36
$6.99
(for a pack of 36 screws)

 



Click on photo for
larger view
Marshall™ HEAD BACK PANEL STAINLESS STEEL SCREWS AND WASHERS (SET OF 4) FOR FULL SIZE HEADS.  Set of 4 screws, Stainless Steel, 1 1/2" long, Phillips, oval head, with matching cup washers.  Fits most large Marshall™ heads starting in the 1990s, including the JCM-900, JCM-2000 and JVM series.   Note:  The screw heads in this package have a slight oval shape, as opposed to many Marshall™ head back panel screws which have a flat head.  This oval shape helps improve the "bite" of the screwdriver, and helps prevent the screw head from being mangled over time.
Part #
MBP-4
$1.49
(for a pack of 4 screws and 4 washers)
 


Click on photo for
larger view

Marshall™ METRIC HANDLE SCREWS
Pack of 2 metric handle screws for Marshall™ MAH-294 handle.   Original Marshall™, designed to work with the OEM metric T-Nuts.   Set of 2 Flat-head counter-sunk Phillips,  M5 x 0.8, length 25 mm.   Found primarily on JCM900, JCM2000, larger Valvestate, and JVM series amps.
Part #SC-404
$1.99
(for a pack of 2 Marshall™ metric screws)
 


Click on photo for
larger view

BLACK HANDLE SCREWS
Pack of 2 stainless-steel handle screws finished in satin black for use with black end-cap handles, such as our GAH-1 or GAH-271B.  1-1/4" Long, 10-32 threads, finished in satin black to match black end caps.   Designed to work with a 10-32 T-Nut, in cabinet wood of 3/4" or less.    Will not work with external nut - must be a T-Nut.   Will not work with cabinet wood thicker than 3/4".   See Data Sheet here
Part #SC-403B
$0.99
(for a pack of 2 screws)
 



Click on photo for
larger view
FENDER SPEAKER MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 12.   Locking nut and washer included.  Phillips head.   Drill hole, insert and tighten screws into wood from front of baffle.  Install grill cloth, and you have professional speaker mounting studs.   Replacement for original Fender™ speaker mounting studs.   Fender™ part number 0992094000.   Set of 12.
Part #SC-409-12
$12.95
(For a pack of 12 screws with nuts and lock washers)
 



Click on photo for
larger view
FENDER SPEAKER MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 4.   Locking nut and washer included.  Phillips head.   Drill hole, insert and tighten screws into wood from front of baffle.  Install grill cloth, and you have professional speaker mounting studs.   Replacement for original Fender™ speaker mounting studs.   Fender™ part number 0992094000.   Set of 4.
Part #SC-409-4
$3.50
(For a pack of 4 screws with nuts and lock washers)
 


Click on photo for
 larger view
Fender Bright Switch Screws, Version 1 (4-40 thread)

Set of 4 screws.   Used to attach the slide type Bright Switch in some Fender amps.   These screws have SAE thread 4-40.  3/16" long with pan head.   Stainless steel, will not rust.   Note:   Not all bright switches use this type of screw.   Some use the SC-305 screw.

Part #SC-440
$0.60
(for a set of 4 screws)


Click on photo for
 larger view
Fender Bright Switch Screws, Version 2 (3 x 0.5M thread)

Set of 4 screws.   Used to attach the slide type Bright Switch in some Fender amps.   These screws have metric thread 3.0 x 0.5.  6mm long with pan head.   Stainless steel, will not rust.   Note:   Not all bright switches use this type of screw.   Some use the SC-440 screw.

Part #SC-305
$0.60
(for a set of 4 screws)


Click on photo for
larger view
ISOLATION WASHER - 3/8" - For #8 Screws

3/8" outside diameter neoprene bonded flat washer. Perfect for bolting speakers to cabinets. It will securely hold the speaker in place and stop any rattling. For use with #8 screws.  Ideal for vintage Fender amps with #8 speaker mounting screws.  Set of 4 washers.

Part #SIW-38-4

$0.59
(For a set of 4 washers)


Click on photo for
larger view
ISOLATION WASHER - 1/2" - For #10 Screws

Larger 1/2" outside diameter neoprene bonded flat washer. Perfect for bolting speakers to cabinets. It will securely hold the speaker in place and stop any rattling.  For use with #10 screws, such as a 10-32 machine screw.  Set of 4 washers.

Part #SIW-50-4

$0.69
(For a set of 4 washers)


Click on photo for
larger view
REPLACEMENT HOUSING SCREWS FOR MXR PEDALS
Set of 4 housing screws for MXR, Way Huge and other pedals which use 6-32 x 1/2" screws, including pedals which use Bud or Hammond style enclosures.

Replacement screws for Dunlop DCB10 DC Brick, MXR M101 Phase 90, MXR M102 Dyna Comp, MXR M103 Blue Box, MXR M104 Distortion+, MXR M115 Distortion III, MXR M132 SuperComp, MXR M133 Micro Amp, MXR M134 Stereo Chorus, MXR M169 Carbon Copy Analog Delay, MXR M173 Classic 108 Fuzz, MXR M182 El Grande Bass Fuzz, MXR MC401 Custom Audio Electronics Boost, MXR MC402 Boost Overdrive, Dunlop ZW44 Zakk Wylde Overdrive and others.

Part #D-ECB590

$0.59
(for a set of 4 screws)


Click on photo for
larger view
GUITAR PICKGUARD SCREWS, CHROME.   Set of 12 chrome screws for electric guitar pickguards.

Part #PGSC-12
$2.49
(pack of 12 screws)
 


Click on photo for
larger view
GUITAR PICKGUARD SCREWS, BLACK.   Set of 12 black screws for electric guitar pickguards.

Part #PGSB-12
$2.49
(pack of 12 screws)
 


Click on photo for
larger view
KEPS NUT, ZINC, 6-32 THREAD, SET OF 4 NUTS.   Typically used on Fender™ speaker baffle mounting on vintage and reissue "tweed" amps.  Works with all 6-32 screws.   Captive lock washer keeps nut tight.   Zinc coating retards oxidation.   Sold in a pack of 4.
Part NT-632-4
$0.59
(pack of 4 nuts)
 


Click on photo for
larger view
KEPS NUT, ZINC, 8-32 THREAD, SET OF 4 NUTS.   Typically used on Fender™ Nickel Chassis Straps bolts, and for speaker mounting.   Works with all 8-32 screws.   Captive lock washer keeps nut tight.   Zinc coating retards oxidation.   Sold in a pack of 4.
Part NT-832-4
$0.69
(pack of 4 nuts)
 


Click on photo for
larger view
KEPS NUT, ZINC, 10-32 THREAD, SET OF 4 NUTS.   Typically used on Fender™ chassis mounting screws on vintage "tweed" amps from the 1950s.  Works with all 10-32 screws.   Captive lock washer keeps nut tight.   Zinc coating retards oxidation.   Sold in a pack of 4.
Part NT-1032-4
$0.79
(pack of 4 nuts)
 



Click on photo for
larger view
Premium-quality steel T-nuts feature three razor-sharp teeth and 8-32 fine thread.  Works with all 8-32 screws - recommended for mounting many guitar amp handles.   Pack of 4 nuts.
Part TNUT-832
99 cents
(pack of 4)
 



Click on photo for
larger view
Premium-quality steel T-nuts feature three razor-sharp teeth and 10-32 fine thread.  Works with all 10-32 screws - recommended for mounting many guitar amp handles.   Pack of 4 nuts.
Part TNUT-1032
99 cents
(pack of 4)
 



Click on photo for
larger view
Premium-quality steel T-nuts feature six razor-sharp teeth and extra-long barrels.  1/4-20 thread.   The result is a T-nut that goes in straighter and holds tighter than ordinary T-nuts. As a bonus, the 6-prong design ensures that your T-nut will stay in place even when working at the edge of a driver hole. We guarantee that these are the finest T-nuts that you will find on the market. Recommended hole size is 5/16", thread is 1/4-20, barrel length is 17/32", or about 13.5mm.     Pack of 4 nuts.
Part 6-TNUT-1/4-20
$1.59
(pack of 4)
 



Click on photo for
larger view
Premium-quality steel T-nuts feature six razor-sharp teeth and extra-long barrels.  1/4"-20 coarse thread. The result is a T-nut that goes in straighter and holds tighter than ordinary T-nuts. As a bonus, the 6-prong design ensures that your T-nut will stay in place even when working at the edge of a driver hole. We guarantee that these are the finest T-nuts that you will find on the market. Recommended hole size is 1/4", thread is 10-32, barrel length is 11mm, or about 7/16".     Pack of 4 nuts.
Part 6-TNUT-1032
$1.59
(pack of 4)
 


Click on photo for
larger view
BLACK PAN-HEAD WOOD SCREWS, #6 X 3/4", PACK OF 10.   Deep threads, sharp point, pan head with Philips drive.  #6 screw, Pack of 10.
Part #SCR-435
$0.79
(pack of 10)
 

BLACK PAN-HEAD WOOD SCREWS, #8 X 1/2", PACK OF 10.   Deep threads, sharp point, pan head with Philips drive.  #8 screw, 1/2 inch long, pack of 10.
Part #BWS8-5
$0.99
(pack of 10)
 

BLACK PAN-HEAD WOOD SCREWS, #8 X 3/4", PACK OF 10.   Deep threads, sharp point, pan head with Philips drive.  #8 screw, 3/4 inch long, pack of 10.
Part #BWS8-75
$1.10
(pack of 10)
 

BLACK PAN-HEAD WOOD SCREWS, #8 X 1", PACK OF 10.   Deep threads, sharp point, pan head with Philips drive.  #8 screw, 1 inch long, pack of 10.
Part #BWS8-1
$1.25
(pack of 10)

BLACK PAN-HEAD WOOD SCREWS, #8 X 1 1/2", PACK OF 10.   Deep threads, sharp point, pan head with Philips drive.  #8 screw, 1-1/2 inches long, pack of 10.
Part #BWS8-15
$1.39
(pack of 10)



Click on photo for
larger view

Nickel-plated Truss-Head Corner Screws 
Flat pan type truss-head corner screws for NON counter-sunk
nickel corners, such as our NPC-157-2, NPC-157-2L and NPC-157-3 corners.  1/2 inch long, Phillips head, nickel plated.   Sold individually.

Part #SC-225

$0.20
(each)
 


Click on photo for
larger view

Black Truss-Head Corner Screws 
Flat pan type black truss-head corner screws for NON counter-sunk black corners, such as our SCC-130-2, SCC-130-2L and SCC-130-3 corners.  1/2 inch long, Phillips head, black powder coated.   Sold individually.

Part #SC-304

$0.20
(each)
 


Click on photo for
larger view
STAINLESS STEEL CHASSIS SCREWS WITH WASHERS, Marshall™ METRIC
Replacements for the standard M6 metric screws used to hold the chassis in virtually every Marshall™ head.  Washers included.   Package of 4 stainless steel screws, with 4 washers.  
Part #MCB-4
$3.99
(Set of 4 screws w/washers)
 


Click on photo for
larger view
STAINLESS STEEL CHASSIS SCREWS WITH WASHERS, Orange™ METRIC
Replacements for the standard M6-1.00 50mm metric screws used to hold the chassis in UK-built Orange™ heads and combos.  Washers included.   Package of 4 stainless steel screws, with 4 washers.  
Part #OCB-4
$4.99
(Set of 4 screws w/washers)


Click on photo for
larger view
STAINLESS STEEL CHASSIS SCREWS WITH WASHERS, Trace Elliot™ METRIC
Replacements for the standard M6-1.00 35mm metric screws used to hold the chassis in UK-built Trace Elliot™ heads and combos.  Washers included.   Package of 4 zinc-plated steel screws, with 4 washers.  
Part #TCB-4
$3.99
(Set of 4 screws w/washers)
 



Click on photo for
larger view
STAINLESS STEEL COMBO CHASSIS SCREWS, Marshall™ METRIC (NOT BLACK!)  SET OF 4 SCREWS.
Unpainted replacements for the standard M6 metric screws used to hold the chassis in virtually every larger Marshall™ combo (typically 50 watts & up).   Note that these screws are plain stainless steel - NOT BLACK LIKE the ORIGINALS.  You may paint the top black if you choose.  We recommend that you only paint the top - do not paint the threads.  35mm long, replaces Marshall part number MESCRW00001.   Found in the JTM610, JTM612, JTM612, JTM615, JTM622, JCM601, JCM602, 2101, 2501, 2502, 4101, 4102, 4501, 4502, TSL601, TSL601, and TSL122.  Set of 4 screws.   See the CW-400-4 washers below for suitable washers.
Part #MCS-5140-4
$2.29
(Set of 4 screws)


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 4.  OD 1/2", ID 3/16"  Typically found on larger combo amp cabinets and 4x12 cabinets, such as Marshall™ .   Set of 4 washers.
Part #CW-400-4
$0.99
(for a set of 4 washers)
 



Click on photo for
larger view
STAINLESS STEEL CHASSIS SCREWS, 10-24 THREAD, SET OF 4 SCREWS.
These 10-24 screws are used on a limited number of amplifiers as chassis mounting screws.   Oval head, 1-1/2 inches long, stainless steel, 10-24 thread.  Set of 4 screws.  Generally used with the extra-large CW-502 cup washer.
Part #SC-412-4
$1.99
(Set of 4 screws)


Click on photo for
larger view
Marshall™ CHASSIS WASHERS
Replacements for the standard washers used with the MCB-4 chassis screws under virtually every Marshall™ head.   Note:  Not for Marshall Combo amps.   Also fits Orange and Trace Elliot amps which use chassis bolts to secure the chassis.  Package of 4 washers.
Part #MCW-4
$1.99
(Set of 4 washers)
 


Click on photo for
larger view
CHASSIS CAGE NUTS, Marshall™ M6 METRIC
Replacements for the standard M6 metric cage nuts used on the chassis in virtually every Marshall™ head.   Package of 4 cage nuts.   Mates with the MCB-4 or MCS-5140-4 screws, above.
Part #MCN-4
$4.59
(Set of 4 nuts)
 



Click on photo for
larger view
CAGE NUT, ZINC, 10-32 THREAD.   Used on square-punched amp chassis rails to secure the chassis to the cabinet.   Frequently found in Peavey, Crate, Ampeg, other brands.   NOT used in Marshall™ - see the MCN-4.   Works with all 10-32 screws.   Verify screw thread before ordering, as not all cage nuts are 10-32.   Zinc coating retards oxidation.   Pack of 4 nuts.   Made in Canada by Hammond Industries.
Part CNA-1421
$4.29
(pack of 4)
 


Click on photo for
larger view
Ground Lug Terminals - Angled
Made from tin-plated brass - will not rust.   Used to connect a ground wire to a screw and nut on a chassis.  Angled, with two holes for soldering wires.   With built-in lock washer to keep the screw and nut from loosening.   Designed for a #8 size screw.   Pack of 5 terminals.

Part #GL-113
$1.39
(Pack of 5 terminals)

 


Copyright ©2024 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
  WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov