Parts for
Hartke
Amps




Click on photo for
larger view		 Ground Lug Terminals - Angled
Made from tin-plated brass - will not rust.   Used to connect a ground wire to a screw and nut on a chassis.  Angled, with two holes for soldering wires.   With built-in lock washer to keep the screw and nut from loosening.   Designed for a #8 size screw.   Pack of 5 terminals.
Part #GL-113		 $1.39
(Pack of 5 terminals)
  


Click on photo for
larger view		 MEDIUM BLACK RUBBER FEET, SET OF 4.  
 
 This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for large rack cabinets or speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw "break-through" and adds overall durability. 1" diameter x 1" tall. Mounting screws not included.

 Part #BRF-1691 		$4.95
(pack of 4)		  


Click on photo for
larger view		 MEDIUM BLACK TAPERED RUBBER FEET, SET OF 4. 
 
This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for rack-mount amps, combo amps, or small speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw "break-through" and adds overall durability. 1" diameter (wide end) x 3/4" diameter (narrow end) x 0.85" tall.  Mounting screws not included.  Set of 4 feet.

 Part #BRF-9105 		$4.95
(pack of 4)		  


Click on photo for
larger view		 MEDIUM BLACK RUBBER FEET, SET OF 4.
  
This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for amp heads, combo amps, or smaller speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw "break-through" and adds overall durability. 1" diameter x 5/8" tall. Mounting screws not included.
 Part #BRF-1692 		$4.95
(pack of 4)		  


Click on photo for
larger view		 POT, Hartke™, PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING
Used in many Hartke™ amp models with PC board circuitry.  Note:  These pots do not fit all Hartke amps.  Compare carefully with the photo, or inquire if unsure.  Diameter of the body of the pot is slightly smaller than a dime.  Shaft length is 10mm.   Click on photo for more detail.  These pots are available with optional dust caps installed.   The dust caps seal out dust for reliability, longer life, and help prevent "scratchy pots" in later life.    Download cross-reference guide for these pots.   Choose pot value and dust cap option in "Select Options".


INCLUDES NUT & WASHER  (For spare or replacement nut, order the PNW-16 nut found in this section)
Part #P-HKE-XX

 $3.95

Select Option 1:


Select Option 2:


Quantity:

W-TAPER


Click on photo for
larger view		 POT, W-TAPER, PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING, KNURLED SHAFT
Found in many Hartke amps as well as other amps and pedals.  Typically used as an EQ pot.   W-Taper pots are reverse audio taper up to the midpoint, but regular audio taper past the midpoint.   Available with or without "center click detent" which marks the midpoint with a slight click you can feel as you turn the pot.  Diameter of the body of the pot is slightly smaller than a dime.  Available in the two most common values of W20K and W100K.   Both values are available with or without the center click detent.  Click on photo for more detail.    

 INCLUDES NUT & WASHER  (For spare or replacement nut, order the PNW-16 nut and washer set found here).
Part #P-W16-XX		 $2.95

Select Option 1:


Select Option 2:


Quantity:

 

Click on photo for
larger view

Available with or without nut and washer.

JACK, 1/4", TIP/SLEEVE 4 PIN, PC MOUNT.   Mono, 4 pin. Fits certain Fender™, Hartke™ and Vox™ amp models 1988 - present.  Replacement nut/washer set is the JN-916.

Available with or without nut/washer - choose in "Options"
Part # J-506		 Starting at $1.99
Select Option:


Quantity:

 

Click on photo for
larger view

Available with or without nut and washer.

JACK, 1/4", TIP/RING/SLEEVE, 7 PIN, PC MOUNT, Fender™, Hartke™, B-52™, Randall™, and Crate™ Amps.  Fender™, Hartke™, Randall™, B-52™ or Crate™ PCB mount 1/4" jack.  7 pins.   Fits several Hartke™ amp models 1990 - present, and several Crate™ models, especially in the GX series.  Used in the Fender™ SKX65R and SKX100R for the input jacks.  Used in some Fender™ Squier and Sidekick amps as the headphone jack.   Replaces Hartke™ part number 350023 and 300519.  Replaces Fender™ part number 022923.  Replacement nut/washer set is the JN-916.

Available with or without nut/washer - choose in "Options"
Part # J-545		 Starting at
$5.95
Select Option:


Quantity:

 

Click on photo for
larger view
 JACK, 1/4", PC MOUNT, STEREO, 5 PINS, SWITCHED, INSULATED.   Both tip and ring are switched (normally closed).   Used in Peavey™ and other brands.  Same as J-523, except that the pins are narrow for insertion into smaller PC holes.  Nut and washer included.

Part #J-527		 $6.95  

 
Click on photo for
larger view		 ECONOMY JACK, 1/4", PC MOUNT, STEREO, 5 PINS, SWITCHED, METAL BUSHING.  
Both tip and ring conductors are switched (normally closed).  5 pins.     Used in Hartke™ KM60, KM100 and KM200.  Hartke part number 371227.  Nut and washer included.

Part #J-529		 $2.99  


Click on photo for
larger view		 ROCKER SWITCH, MARSHALL™, HARTKE™, OTHERS, LARGE WIDE BLACK
Has 4 electrical terminals on back of switch (DPST).   Termination is 0.187" (4.8mm) push-on terminals.   Made for 0.73" H x 0.85" W mounting hole (19.0mm X 22mm).   Rated 15A @ 125VAC.    Commonly found on Hartke™ amp models HA1400, HA2500, HA3500C, HA4000, HA5000, HA5500, HA7000 and other models.  Hartke™ part number 8-S310BBIWQ420.   
 Part #SW-1802		 $4.95  


Click on photo for
larger view		 IEC POWER CONNECTOR, NON-FUSED, WIRED TYPE, SNAP-IN ATTACHMENT TO PANEL
Popular IEC type AC connector found in many amplifiers and effects units.   Designed to snap into 0.8" x 1.10" rectangular panel hole.  Connections are for 1/4" push on terminals, or may be soldered.  Rated at 10 amps.   Found in the Hartke 3500 MOSFET.   Hartke part number 300308.
Part #P-S2-108		 $2.95  


Click on photo for
larger view		 IEC POWER CONNECTOR, FUSED, WIRED TYPE, SCREW ATTACHMENT TO PANEL.
Popular IEC type AC connector found in many Orange™ amplifiers.   Designed for screw mounting into 1.25" x 1.10" rectangular panel hole.   Uses GMA type fuses (5mm x 20mm).   Space for spare fuse.   Rated up to 10 amps.   Fuse not included.   Hartke part number 8-40010014.   Used on the Hartke LH500 and LH1000 Amps.
Part #P-S2-719		 $3.95  


Click on photo for
larger view		 Revisit™ 6 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 6 ft LONG, IEC CONNECTOR AT EQUIPMENT END.  Common replacement cord for use on many guitar amps, power amps, effects units, etc.   Standard NEMA 5-15 plug for North American use at 110-120 Volts AC.    IEC connector at equipment end.   Used only in North America.
 Part #PC-300		 $6.95  


Click on photo for
larger view		 Revisit™ 10 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 10 ft LONG, IEC CONNECTOR AT EQUIPMENT END.   Replacement Cord For Many Guitar Amps, Power Amps, Effects Units, Etc. 10 Ft Length Give Extra Flexibility In Equipment Placement, Reduces Use Of Extension Cords.   Standard NEMA 5-15 plug for North American use at 110-120 Volts AC.    IEC connector at equipment end.   Used only in North America.
 Part #PC-600		 $10.95  
 

Strat™, Stratocaster™, Esquire™, Telecaster™, Tele™, Jazzmaster™, Jaguar™, Mustang™, P.Bass™, J.Bass™ and Fender™ are registered trademarks of Fender™ Musical Instruments. The replacement necks and bodies are for a Fender™ or Squier™ by Fender™ guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster™, Telecaster™, J.Bass™, P.Bass™ and Tele™ Bass are registered trademarks of Fender™ Musical Instruments Co.  
Peavey™ is a registered trademark of Peavey™ Electronics Corporation.
Marshall™ is a registered trademark of Marshall™ Amplification Plc.
Mesa Boogie™ is a registered trademark of MESA/Boogie™ Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2023 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
  WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov