Peavey Fuse Holders and Lamps

Click on photo for
larger view
FUSE HOLDER, HIGH QUALITY, FITS AGC, MDL OR 3AG TYPE FUSE. 
Fuse holder, Twist-lock cap.   Durable, rugged design - better than OEM.   Low profile so that cap does not extend beyond rear amp cabinet.   Fits "American" style AGC, MDL, OR 3AG fuses (1/4" x 1 1/4")  Connection by 1/4" push-on terminals, or wires may be soldered to the terminals.
Part #FH-301
$3.95


Click on photo for
larger view
FUSE HOLDER, HIGH QUALITY, FITS AGC, MDL OR 3AG TYPE FUSE. 
Fuse holder, Twist-lock cap.  Low profile so that cap does not extend beyond rear amp cabinet.   Fits "American" style AGC, MDL, OR 3AG fuses (1/4" x 1 1/4")  Connection by 3/16" push-on terminals, or wires may be soldered to the terminals.  
 Fits through a .50" hole in the chassis.
Part #FH-367
$8.95  


Click on photo for
larger view
FUSE HOLDER -  Peavey™, Fender™, many other brands - AGC, 3AG or MDL (1/4 inch x 1 1/4 inch) TYPE FUSE
Fuse holder found in many styles of guitar amplifiers, power amps and effects units.  For example, this fuse holder is used in the Peavey Valve King series.  PC Board mounted.   Uses AGC, MDL, OR 3AG type 1/4" x 1 1/4" fuse.  Fuse cap is removed and inserted with flat screwdriver.
Part #FH-2709
$11.95


Click on photo for
larger view
REPLACEMENT CAP FOR FUSE HOLDER - Peavey™
Cap for fuse holder found in many Peavey™ products.   Common failure item in Peavey™.   Original Peavey™ part number
30900281.   For AGC, MDL, OR 3AG type 1/4" x 1-1/4" fuses.
Part #FH-203
$7.95

 


Click on photo for
larger view
FUSE CLIP -  Peavey™, Fender™,  many other brands - GMA OR GDC TYPE FUSE (5mm x 20mm)
Fuse clips found in many styles of guitar amplifiers, power amps and effects units.  PC board mounted.   ONLY for the smaller European style 5mm x 20mm fuse (3/16" x 3/4" fuse).  Sold in pairs.
Part #FC-520
$0.59
(for a set of 2 fuse clips)


Click on photo for
larger view
IEC POWER CONNECTOR, PEAVEY, NON-FUSED, PCB MOUNT
Used in the Peavey 6505+ 112 Combo (not 6505 or 6505+ heads), ValveKing series, including the ValveKing 112 and 212 combos, and the ValveKing Head amplifiers.  Also used in the XR684 and XR1600F Powered Mixers, and the Peavey S14 and S24 mixing consoles.  Original Peavey part number 70901428 and 30901428.   Datasheet here.

Part #30901428
$5.95  


Click on photo for
 larger view
VINTAGE RED INDICATOR LIGHT - 120 VOLT.
Indicator light, round. 120 Volts.  3/8" mounting hole.   A replacement for early Peavey models with the round red front panel pilot light, which is no longer available.   120 volt neon lamp - designed to run on the switched line voltage (North America only).   Mounting nut is included.
Part #MPL-6010R
$12.95  


Strat™, Stratocaster™, Esquire™, Telecaster™, Tele™, Jazzmaster™, Jaguar™, Mustang™, P.Bass™, J.Bass™ and Fender™ are registered trademarks of Fender™ Musical Instruments. The replacement necks and bodies are for a Fender™ or Squier™ by Fender™ guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster™, Telecaster™, J.Bass™, P.Bass™ and Tele™ Bass are registered trademarks of Fender™ Musical Instruments Co.  
Peavey™ is a registered trademark of Peavey™ Electronics Corporation.
Marshall™ is a registered trademark of Marshall™ Amplification Plc.
Mesa Boogie™ is a registered trademark of MESA/Boogie™ Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2024 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
  WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov