Prices good now through July 31, 2015
(while supplies last)


Click on photo for
larger view
POT - FENDER BRACKET MOUNT SNAP-IN 50K LINEAR TAPER WITH CENTER DETENT.  Original Fender part number 0027942000.   Used in several Fender products - often used as a tone control, with the detent or notch at the midway position.   INCLUDES NUT & WASHER 
Part #FPHD-50KL-DSCD
$2.99  




Click on photo for larger view

 
Accutronics Reverb Tank, 17" long, 3 spring   Input impedance 10 ohms, output impedance 2575 ohms, long decay (2.75 - 4 seconds), input insulated/output grounded, designed for horizontal mounting, open side down.   Common replacement for Fender®.   Upgrade for the 4AB3C1B 2-spring tank.   See explanation of Accutronics reverb tank numbering system here

Made in South Korea by Accu-Bel.

Part #ACC-9AB3C1B
Limited quantity - 1 only left in stock.

$29.99
In stock
Limited quantity - 1 only left in stock.


Limited quantity - 1 only left in stock.

Adapter, 1/4" STEREO PLUG TO STEREO 1/8" JACK
Used to adapt standard sized 1/4" headphone jack to mini 1/8" headphone plug.
Part P-111
$1.99
Limited quantity - 2 only left in stock.


Limited quantity - 2 only left in stock.


Click on photo for
larger view
 
Clone of the Fender KNOB, Vintage Cream, Set of 5
Similar to
Fender part number 0990933000.  "Cupcake" barrel knob, cream white. With set-screw.   All plastic - no brass insert.  Made for smooth 1/4" shaft. as used by:
Fender® 1960-1964 for the Fender Bassman, Showman and Bandmaster Amp, and for several Fender Custom Shop and Fender Reissue amps:  Tone Master, Custom Vibrolux Reverb, Vibroking, Super Sonic Amp (blonde) etc.  Set of 5 knobs.   Limited quantity - only one set left in stock.

Part #K-315A-5
$5.95
(for pack of 5 knobs)
Limited quantity - only one set left in stock.
 


Limited quantity - only one set left in stock.


Click on photo for
larger view
Genuine  Eminence Diaphragm
8 Ohms

REPLACEMENT 8-OHM AUDIO DIAPHRAGM.  TITANIUM COMPRESSION DRIVER, 2" DIAMETER VOICE COIL, 80 WATTS, 8 OHM IMPEDANCE, 1,200-20,000HZ.   USED IN MANY PROFESSIONAL HORN DRIVERS, INCLUDING YAMAHA AND CARVIN.
Part #
PSD2002-8DIA
We have just one of these left in stock!

$33.95
Stock no:
PSD2002-8DIA
8 Ohms
$33.95


Click on photo for
larger view
Genuine  Eminence Diaphragm
16 Ohms

REPLACEMENT 8-OHM AUDIO DIAPHRAGM.  TITANIUM COMPRESSION DRIVER, 2" DIAMETER VOICE COIL, 80 WATTS, 16 OHM IMPEDANCE, 1,200-20,000HZ.   USED IN MANY PROFESSIONAL HORN DRIVERS, INCLUDING YAMAHA AND CARVIN.
Part #
PSD2002-16DIA

$33.95
Stock no:
PSD2002-16DIA
16 Ohms
$33.95

A quick drying adhesive that is specially designed for speaker repair. It forms a hard, durable and vibration resistant bond with minimal shrinkage.  Great for foam surround and dust cap attachment. Black in color.  Two applicator brushes included.  Direct cross to Moyen Speaker Repair Adhesive Part No. RS-3087. Sold only in the United States
Part SCC-8337

Two ounce (55ml) bottle of MG Chemicals Speaker Service Cement
$12.99

Sold only in the United States

Standard Piezo Horn Driver - 100W Max
Due to the high efficiency of the piezo system, the loading on the amplifier is negligible. For use with any reflector horn with 1 3/8" thread connection.
* Highly efficient Piezo system
* Impedance - 1k ohms @ 1kHz
* Impedance - 50 ohms @ 25kHz
* Frequency response - 3kHz – 29kHz
* Body diameter - 2.5 inches

Part #DUV-100
$2.99  

 

Heavy Duty Piezo Horn Driver - 300W Max
Due to the high efficiency of the piezo system, the loading on the amplifier is negligible. For use with any reflector horn with 1 3/8" thread connection.
* Highly efficient Piezo system
* Impedance - 1k ohms @ 1kHz
* Impedance - 50 ohms @ 25kHz
* Frequency response - 3kHz – 29kHz
* Body diameter - 4.1 inches

Part #DUV-300
$3.99  

Dual Element Piezo Tweeter Horn
Super bargain price on these versatile tweeters! Used in both home stereo and professional applications. Adds high frequency response to stereo cabinets, PA cabinets, monitor speakers, DJ enclosures. No crossover needed - a series resistor (50 ohms, 5 watts) may be used on high powered systems to prevent distortion. Piezo tweeters are high impedance - their effect on your
overall system impedance is negligible.
Part #DPZ-1
$3.99



AC-DC Adapter
Input Voltage:   120V AC, 60Hz
Output Voltage:   9V DC, 200mA
Barrel Connector Size:    2.1mm ID x 5.5mm OD
Polarity: 


Common configuration
for guitar effects pedals 
For use on 110-120VAC System only, as found in North America.

Part #134-025

$9.99

AC-DC Adapter
Input Voltage:   120V AC, 60Hz
Output Voltage:   9V DC, 1200mA (1.2A)
Barrel Connector Size:    2.1mm ID x 5.5mm OD
Polarity: 


Common configuration
for guitar effects pedals. 
For use on 110-120VAC System only, as found in North America.

Part #130-526

$19.99  


AC-DC Adapter
Input Voltage:   120V AC, 60Hz
Output Voltage:   12V DC, 1500mA (1.5A)
Barrel Connector Size:    2.1mm ID x 5.5mm OD
Polarity:  




Common configuration
for guitar effects pedals. 
For use on 110-120VAC System only, as found in North America.

Part #203-036

$23.99


AC-AC Adapter
Input Voltage:   120V AC, 60Hz
Output Voltage:   12V AC, 1500mA (1.5A)
Barrel Connector Size:    2.1mm ID x 5.5mm OD
Polarity:   No Polarity - This is 12V AC output


Common configuration for guitar effects pedals requiring a 12 Volt AC Adapter @1500mA, rather than DC. 
For use on 110-120VAC System only, as found in North America.

Part #167-151

$19.99


Click on photo for
larger view

Click here for circuit wiring diagram

TRUE BYPASS PC BOARD.
Designed to work with the FS-501-PC footswitch, above.    Greatly simplifies converting your pedal to true-bypass.   PC board solders directly to the 9 pins of the FS-501-PC, and wires then are connected from the 8 terminals on the edge of the PC board to the board, input/output jacks, LED, ground, etc.  This board grounds the effects input in bypass mode, which helps to reduce pops and noise.  Adding this board to the FS-501-PC and installing in your pedal will give it true bypass and the capability for a effects on/off LED.  Note:   Your pedal must have a hand-wired footswitch such as the FS-435, FS-492, FS-497, FS-498.   For best results, it should also have hand-wired input and output jacks.   Also, there must be sufficient room to mount the FS-501-PC switch, which is a little larger than the FS-435, FS-492, and FS-497 (it's about the same size as the FS-498).   If your existing footswitch is momentary or PC board mounted, this conversion will not work on your pedal.  Click here for circuit wiring diagram.
Part #PCB-200A
$1.00  


Click on photo for
larger view
CEN-TECH DIGITAL MULTIMETER

Digital Multimeter gives you accurate digital readings for 7 functions: AC/DC voltage, DC current, resistance, transistor test, diode test, and battery test, all easily read on the large, easy-to-read LCD display. Positive set selector switch. 32" leads included.
* Automatic zero adjust
* 2.5x second sample time
* Over-range indicator
* Low-battery indicator
* Fuse and diode-protected circuit
DC amps: 0-200 microns
A-2000 microns
A-20mA-200mA
Resistance: 0-200-2000-20K-200K-2000K ohm
DC voltage: 0-200mV-2000mV-20V-200V-1000V
AC voltage: 0-200-750V

Part #98025

$5.99

RESISTOR, CARBON COMPOSITION.    New production, 1/2 watt.   100K Ohms, 5%.    Common size for plate resistors in vintage Fender amps!
Part #100KCC1/2
Special Price!
$0.42


Click on photo for
 larger view
3/16" FEMALE QUICK CONNECT TERMINAL CONNECTOR - 14GA or 16GA wire. 
For connections to speakers in many amplifiers.   For ¼" width terminals.   Blue - designed for 14-16ga wire.    Requires standard crimp terminal tool for proper wire connection.   Pack of 12 connectors.

Part #FC-1250-WS
$0.99
(for 1 dozen connectors)
Regularly $1.29
 


Click on photo for
 larger view
3/16" FEMALE QUICK CONNECT TERMINAL CONNECTOR - 18GA-22GA
For connections to speakers in many amplifiers.   For 3/16" width terminals. Red - designed for 18-22ga wire.    Requires standard crimp terminal tool for proper wire connection.   Pack of 12 connectors.

Part #FC-1150-WS
$0.99
(for 1 dozen connectors)
Regularly $1.29
 


Click on photo for
 larger view
1/4" FEMALE QUICK CONNECT TERMINAL CONNECTOR - 14GA or 16GA wire. 
For connections to speakers in many amplifiers.   For ¼" width terminals.  Blue - designed for 14-16ga wire.    Requires standard crimp terminal tool for proper wire connection.   Pack of 12 connectors.

Part #FC-1
225-WS
$0.99
Regularly $1.29
 


Click on photo for
 larger view
1/4" FEMALE QUICK CONNECT TERMINAL CONNECTOR - 18-22GA WIRE
For connections to speakers in many amplifiers.   For ¼" width terminals.  Blue - designed for 18-22ga wire.    Requires standard crimp terminal tool for proper wire connection.   Pack of 12 connectors.

Part #FC-1
125-WS
$0.99
(for 1 dozen connectors)
Regularly $1.29
 


Click on photo for
larger view
LARGE BLACK RUBBER FEET, SET OF 4.   TAPERED -  1 5/8" DIAMETER AT TOP, 1 1/4" AT BOTTOM.  3/4" TALL.  BLACK RUBBER WITH METAL INSERT.   USED TO SUPPORT AMP HEADS, SPEAKER CABINETS.
Part #BRF-9107-WS
$5.95
(pack of 4)
(Regularly sells for $7.95!)
 


Click on photo for
 larger view
PLUG, MALE XLR TYPE, NICKEL
Heavy-duty construction.  3-pin, similar to Switchcraft A3M. 
Part XLR-A3M-WS
$1.69
(regularly sells for $2.25!)
 


Click on photo for
 larger view
PLUG, FEMALE XLR TYPE, NICKEL
Heavy-duty construction.  3-pin, similar to Switchcraft A3F. 
Part XLR-A3F-WS
$1.69
(regularly sells for $2.25!)
 


Click on photo for
 larger view
Adapter, MALE-MALE XLR TYPE, NICKEL
Heavy-duty construction.  3-pin, similar to Switchcraft 390. 
Part XLR-390-WS
$1.99
(regularly sells for $2.99!)
 


Click on photo for
 larger view
COUPLER, FEMALE-FEMALE XLR TYPE, NICKEL
Heavy-duty construction.  3-pin, similar to Switchcraft 389. 
Part XLR-389-WS
$1.99
(regularly sells for $2.99!)

UNIVERSAL LIGHTED ROCKER SWITCH

Has 3 electrical terminals on back of switch. 1/4" push-on terminals, or solder directly to terminals. Rated 15A @ 125VAC, 10A @ 250VAC. Internal neon lamp powered by either 125VAC or 250VAC. Designed for 1 1/8" x 9/16" rectangular mounting hole. Used in several brands of amplifiers and effects as the main power switch.

Part #SW-25-WS     1.99
Only 1 left in stock!


 

Quality 25 watt Soldering Iron at a Budget Price!

25-Watt Pencil Soldering Iron with Bakelite construction, nickel-plated and iron-clad conical tip. Compare with soldering irons costing several times more!  120VAC.   For use on 110-120VAC System only, as found in North America.


74B25        $3.99

 

 

Laser Pickup KSS-210A, KSS210B, KSS-212A, KSS212B

The most common CD laser pickup found today! The KSS-210A can also be used to replace the KSS-210B, KSS-212A and KSS-212B. Original Sony part number 8-848-062-11. Found in CD Players under many different brand names. Selling for up to $45.50 elsewhere.  (Note:  soldering capability and solder wick required to remove static-protection shorting link upon installation.)  Not for use in Aiwa brand CD Players.   Our price is regularly $19.95 - save 25%!
Instructions for installation (PDF)

KSS-210A-WS
$14.95 ea!

Note:  No refunds are given on laser pickups.
Defective pickups are handled in accordance with the manufacturer's warranty (like for like replacement)

Laser Pickup KSS-213B,
KSS-213C

Very popular CD laser pickup found in many makes and models! Original Sony part number 8-848-379-31 and 8-848-482-02.  Also replaces KSS-213C.  Selling for up to $47.50 elsewhere.  (Note:  soldering capability and solder wick required to remove static-protection shorting link upon installation.)   Our price is regularly $19.95 - save 25%!

Instructions for installation (PDF)
KSS-213B-WS
$14.95 ea!

 

 

Note:  No refunds are given on laser pickups.
Defective pickups are handled in accordance with the manufacturer's warranty (like for like replacement)

 

Copyright ©2015 Studio Sound Electronics - All Rights Reserved