AC Adapters


Click on photo for
larger view

REVISIT EFFECTS PEDAL POWER SUPPLY 9V DC, 1.6 amps.   Input voltage from 100V AC to 240V AC.   Output 9 volts DC, 1600mA, fully regulated.   Connector is a 2.1mm inner diameter, center negative, outside sleeve positive.  Perfect for most pedals which are 9V battery powered.   This compact supply will power up to 10 pedals (assuming each pedal requires 160mA or less).   For powering multiple pedals, see the DCC10X8 cable, below.
Part #PPS-916
$14.95 


Click on photo for
larger view

REVISIT PEDAL POWER DAISY CHAIN CABLE
Connect up to 10 Pedals with this Power Cable from a single power supply.  This daisy chain is the industry standard 2.1mm size. There are 1 in and 10 outs. It is well made, has right angle plugs and built with 22AWG wire.  Total length is 8 feet.  The amperage capacity of the power supply you use with this cable needs to be at least as large as the sum of all of the current requirements of your pedals.   For example, if each pedal requires 160mA (or 0.16 amps), the power supply needs to be capable of at least 10 x 0.16 = 1.6 amps (or 1600mA) 

Part #DCC10X8
$11.95  


Click on photo for
larger view

REVISIT POLARITY REVERSING ADAPTER CABLE
Fixes the frustrating problem of having a power supply designed for "center pin positive" and a pedal which requires "center pin negative".  Or vice-versa!   This ingenious adapter cable reverses the center pin with the outside ring, allowing you to successfully use a "backwards" pedal with your pedal power supply.  The connectors are the popular 2.1mm x 5.5mm size.  5 inches long.

Part #PRC-129
$2.29  


Click on photo for
larger view

POWER CONNECTOR ADAPTER 2.1mm to 2.5mm
The two most common connectors for AC adapters are 2.1mm x 5.5mm and 2.5mm x 5.5mm.    The outside diameter of these connectors are identical, but one uses a larger pin than the other, and therefore they are not compatible.   This adapter has a 2.1mm pin in the back, with a 2.5mm hole in the front, for cases where the pin in your pedal is just a tiny bit too large for the adapter.
Part #195-3591
$2.99 


Click on photo for
larger view

POWER CONNECTOR ADAPTER 2.5mm to 2.1mm
The two most common connectors for AC adapters are 2.1mm x 5.5mm and 2.5mm x 5.5mm.    The outside diameter of these connectors are identical, but one uses a larger pin than the other, and therefore they are not compatible.   This adapter has a 2.5mm pin in the back, with a 2.1mm hole in the front, for cases where the pin in your pedal is just a tiny bit too small for the adapter connector, and your power is intermittent when you move the adapter cable.
Part #195-3604
$2.99 


Click on photo for
larger view

DC POWER JACK
Handy way to add a power jack for an AC/DC adapter to an existing devices.   Connector fits the popular 2.1mm x 5.5mm barrel plug found on many adapters.   Normally closed switch, so that an internal battery may be switched on or off automatically as the adapter is connected.   Plastic housing isolates both conductors, so it may be used for either center positive or center negative adapters.  Fits 1/2" chassis hole.
Part #J-750
$1.49 


Click on photo for
larger view

DC POWER JACK
Replacement Barrel DC power jack for many pedals, keyboards, etc which use a PC board mounted DC power jack.  Connector fits the popular 2.1mm x 5.5mm barrel plug found on many adapters.   Normally closed switch, so that an internal battery may be switched on or off automatically as the adapter is connected.   Plastic housing isolates both conductors, so it may be used for either center positive or center negative adapters. 
Part #BJK-118
$0.99  


Click on photo for
larger view

1/8" MINI JACK
Switched two-conductor 1/8" mini jack.  Exact replacement for the DC power jack used in the vintage Electro-Harmonix Big Muff and Small Stone, Proco Rat Big Box Reissue and others.
Part #J-218
$0.99  


Click on photo for
larger view

POWER BARREL PLUG
Replacement barrel power plug for many AC adapters.  Connector is the popular 2.1mm x 5.5mm barrel plug found on many adapters.   Soldering required to attach to cable. 
Part #BP-573
$0.99  



Click on photo for
larger view
9V BATTERY CLIP.
Commonly found in effects boxes.   Simple, yet durable construction.  5-3/4" red and black leads.

Part #9VBC
$0.45  


Strat™, Stratocaster™, Esquire™, Telecaster™, Tele™, Jazzmaster™, Jaguar™, Mustang™, P.Bass™, J.Bass™ and Fender™ are registered trademarks of Fender™ Musical Instruments. The replacement necks and bodies are for a Fender™ or Squier™ by Fender™ guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster™, Telecaster™, J.Bass™, P.Bass™ and Tele™ Bass are registered trademarks of Fender™ Musical Instruments Co.  
Peavey™ is a registered trademark of Peavey™ Electronics Corporation.
Marshall™ is a registered trademark of Marshall™ Amplification Plc.
Orange™ is a trademark of Orange Amplification
Vox™ is a trademark of Vox Amplification Ltd.
Egnater™ is a trademark of Egnater Amplfication
Mesa Boogie™ is a registered trademark of MESA/Boogie™ Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2024 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
  WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov